FishyHub
SEACHEM PHOSBOND 100ML BAGGED (SC-1260)
Click to enlarge

Unless stated otherwise, photos show the species, not the exact fish you'll receive.

SEACHEM PHOSBOND 100ML BAGGED (SC-1260)

SGD 23.90

Delivery Information

Delivery takes 3 to 7 working days normally. Delivery fees will be shown upon checkout. Certain areas may require additional charges, and a top-up via PayNow will be needed. This includes Central Business District, Offices, Airport, Hospitals, Tertiary campuses, PSA terminals, Cargo Complexes, cargo ports, shipyards, Government buildings, secured compounds, SAF campus, Marina Bay Sands, Robinson, Marina Square,Orchard, Bras Basah, Sentosa, Tuas, Jurong Island, etc. Our customer service representatives will reach out to you if necessary.

Product Variations

Quantity

Stock: 20

Product Description

PhosBond rapidly removes phosphates and silicates simultaneously from saltwater and freshwater. It is highly efficient and durable, and does not break down easily due to mechanical stress.

Advantages
PhosBond is a revolutionary new product that combines the phosphate removing capabilities of both aluminium oxide and granular ferric oxide into a singular material forming a synergistic effect. It rapidly removes phosphates and silicates from saltwater and freshwater, combining the best of both types of phosphate removers. Its high porosity and surface area give it a large binding capacity, while its physical strength and integrity assures that it will not break down from mechanical stress.

Directions
For best results, PhosBond should be rinsed before use and placed so as to maximise the flow of water through it but not so that it tumbles against itself in flow. It may be used in a canister filter, media chamber, box filter, or any high flow area of a trickle filter. Use of a filter bag such as The Bag is recommended.

Use 60 mL (1/4 cup) for every 200 L (50 US gallons) saltwater or 400 L (100 US gallons) freshwater. Leave product in place for 4 days, then test phosphate or silicate concentrations with either MultiTest Phosphate or MultiTestSilicate. If the concentration of the component you are trying to decrease has not dropped to around 0.02 mg/L, then replace the PhosBond, otherwise leave in place until levels begin to climb again. As long as concentrations remain under control, the product is not exhausted. Over treating is not recommended. PhosBond is not an exchange resin and does not release anything into the water. It does not leach phosphate or silicate back into the water and may be removed, dried, and returned to service until exhausted. Continuous use of small quantities is better than intermittent use of larger quantities.

FAQ
How do I use PhosBond? How long does it work and when is it exhausted?
A: PhosBond Is best used in smaller quantities and changed frequently. In an environment with an excessively high phosphate reading, PhosBond will exhaust rapidly (4 - 5 days). Place the product in a high flow rate area and test your phosphate levels, changing as needed. When you see that your level is below 0.2 ppm (mg/L) leave that portion of PhosBond in the filter. Continue to test weekly for phosphate until you see it begin to rise again. You will then know that it is time to change the PhosBond. If you have low levels of phosphate the PhosBond will absorb the silicate in your system. It is inert and safe to leave in your filter.

You claim that PhosBond has a high capacity, but Company X claims that their GFO has a capacity that is many times higher. Is this false advertising?
A: It is actually quite easy to change the apparent capacity of a GFO during testing. If the capacity of a GFO is tested at an extremely low pH with a phosphate concentration that is much higher than the media can completely, the media will temporarily absorb much more phosphate than it would under ordinary aquarium conditions. We have no interest in artificially puffing up our numbers, so the capacity we have listed is the amount of phosphate that the media can completely remove (without releasing back into the water) in a pH of 8.4.

Can I use PhosBond in a media reactor?
A: We do not recommend it, as the tumbling action of a media reactor can cause this media to produce dust.

How is this different from PhosGuard, PhosNet, and phosfiltrum (aquavitro)?
A: The main difference between these medias is capacity. PhosGuard has the lowest capacity at 0.82 mg/g of PO4 bound, but is the most economical of the four medias. PhosBond has a higher capacity than PhosGuard at 1.19 mg/g of PO4 bound, and combines the benefits of PhosGuard and a pure GFO (strength, high capacity, and rapid phosphate absorption) while still being very economical. PhosNet has the highest capacity of the Seachem phosphate absorbers at 1.41 mg/g of PO4 bound, and is a pure GFO media. Our aquavitro phosfiltrum is a super-high capacity GFO (1.71 mg/g of PO4 bound) that produces very little dust. This media has a higher capacity than any other GFO on the market.

I was told that products that contain aluminium oxide will release aluminium, which will close corals for weeks and might even damage them. Is this accurate?
A: In recent years, there has been speculation that aluminium oxide based phosphate removers like PhosBond release aluminium into the water and subsequently damage corals. The evidence to support this claim was largely anecdotal.

So, through a series of controlled experiments in both freshwater and saltwater, we intended to address both the question of aluminium solubility and aluminium toxicity. The results of these experiments show that under reef conditions (pH near 8) there is no detectable soluble aluminium released from alumina. Under conditions of low pH and high dosage levels, soluble aluminium can be released from alumina; at three times the label dosage rate, we detected 0.2 mg/L aluminium at a pH of 5.3.

Additionally, aluminium oxide is not easily absorbed into the cell to cause negative reactions. Even at three times the dose, soft-bodied corals such as Sarcophyton remain unaffected.

Company X says that I do not need to replace their phosphate absorber for several months, while your instructions say that PhosBond needs to be replaced every 4 days when reducing phosphate. Does not that make PhosBond an inferior product?
A: Not at all! If it takes a phosphate absorber several months to reach its full capacity when the tank has high phosphates, it means that the media is exceptionally slow at absorbing phosphate. PhosBond needs to be replaced every 4 days as long as there is a phosphate problem because, given an infinite amount of available phosphate, PhosBond absorbs phosphate so quickly that it reaches its full capacity in 4 days. The 4 day replacement period is a function of how quickly the media works, not a function of how high a capacity the media has.

More from N30 Ang Mo Kio

N30 Ang Mo Kio

N30 Ang Mo Kio

View Store →

Similar Filter Media You May Like

BOYD Chemipure GREEN (crystal clear water in planted aquarium) - 156g/ 312g
BOYD Chemipure GREEN (crystal ..
SGD 21.50
CARIBSEA BIOMAGNET CLARIFIER 8OZ
CARIBSEA BIOMAGNET CLARIFIER 8..
SGD 14.50
ISTA DISPOSABLE FILTER CARTRIDGE
ISTA DISPOSABLE FILTER CARTRID..
SGD 4.50
FLUVAL 106/206, 107/207 Nitrite Remover
FLUVAL 106/206, 107/207 Nitrit..
SGD 7.15
ANS Microfibre Wool ( Various Size ) filter wool
ANS Microfibre Wool ( Various ..
SGD 3.50
SEACHEM PHOSBOND 1L (SC-1265)
SEACHEM PHOSBOND 1L (SC-1265)
SGD 78.70
SEACHEM PURIGEN 250ML (SC-166)
SEACHEM PURIGEN 250ML (SC-166)
SGD 40.20
Ocean Free Super Pro Peat Granules FM-09 500ml
Ocean Free Super Pro Peat Gran..
SGD 8.80
XinYou XY-1813 Black Sponge
XinYou XY-1813 Black Sponge
SGD 2.20
BIOHOME PLUS 5KG FILTER MEDIA
BIOHOME PLUS 5KG FILTER MEDIA
SGD 214.50
SEACHEM MATRIX 20L (SC-111)
SEACHEM MATRIX 20L (SC-111)
SGD 392.10
UP AQUA G-059F FILTER CARTRIDGE (2pcs/pack)
UP AQUA G-059F FILTER CARTRIDG..
SGD 5.60
ZISS ZM-1 MICRO MOVING MEDIA 1L
ZISS ZM-1 MICRO MOVING MEDIA 1..
SGD 19.80
DYMAX ANTI AMMONIA ROCK 500G
DYMAX ANTI AMMONIA ROCK 500G
SGD 8.80
ANS Carbon Pure 200/Nano
ANS Carbon Pure 200/Nano
SGD 4.00
SEACHEM TIDAL 75 ZEOLITE 250ML (SC-6514)
SEACHEM TIDAL 75 ZEOLITE 250ML..
SGD 19.10
Aquarium Systems Waste Away Gel Large x2
Aquarium Systems Waste Away Ge..
SGD 35.75
Jeneca Replacement Wool - GLB-01/03/04
Jeneca Replacement Wool - GLB-..
SGD 3.00
Powerhouse Filter Media: Soft Type S (prevent pH increase)
Powerhouse Filter Media: Soft ..
SGD 50.00
Oase BioMaster Filter Foam - (20ppi Blue / 30ppi Orange)
Oase BioMaster Filter Foam - (..
SGD 19.80
SEACHEM POND MATRIX 4L (SC-2119)
SEACHEM POND MATRIX 4L (SC-211..
SGD 104.30
SEACHEM MATRIX 250ML (SC-116)
SEACHEM MATRIX 250ML (SC-116)
SGD 11.40
ROWAPHOS PHOSPHATE REMOVAL MEDIA 5KG
ROWAPHOS PHOSPHATE REMOVAL MED..
SGD 273.90
[OF Ocean Free] 3DM Biological Filter Medium - Nugget S
[OF Ocean Free] 3DM Biological..
SGD 9.68
ANS Ammo Ex 1kg w/net
ANS Ammo Ex 1kg w/net
SGD 6.50
BACTERIA KING 10LITRES
BACTERIA KING 10LITRES
SGD 136.00
N30 TANK PREMIUM HONEYCOMB FILTER CLOTH 1000MM X 500MM (N0020)
N30 TANK PREMIUM HONEYCOMB FIL..
SGD 11.00
ANS Micro Filter bag (S/M/L/XL)
ANS Micro Filter bag (S/M/L/XL..
SGD 3.70
ORCA LABS Phospha-Guard BIO-Cubes (250ml - 5L) long term reduce phosphate
ORCA LABS Phospha-Guard BIO-Cu..
SGD 20.00
TUNZE COMLINE REEFPACK 100
TUNZE COMLINE REEFPACK 100
SGD 240.90
SUNSUN T-30/32 Washable wool (50x11x2cm)/ (50x40x2cm)
SUNSUN T-30/32 Washable wool (..
SGD 4.00
DYMAX BIOSPHERE M-SIZE 1L
DYMAX BIOSPHERE M-SIZE 1L
SGD 24.20
TUNZE COMLINE REEFPACK 250
TUNZE COMLINE REEFPACK 250
SGD 330.00
AMAZON Series Chemical Reduction Filter Sponge (Options Available)
AMAZON Series Chemical Reducti..
SGD 8.80
SUNSUN Replacement Sponge for HN-011/ 012
SUNSUN Replacement Sponge for ..
SGD 2.20
JBL Symec XL
JBL Symec XL
SGD 13.30
BOYD Chemi Bags (2bag per pack)
BOYD Chemi Bags (2bag per pack..
SGD 11.50
ANS Mini Bacteria House Rod 1kg
ANS Mini Bacteria House Rod 1k..
SGD 22.00
Back to Nature Aquarium Cleaner 400g
Back to Nature Aquarium Cleane..
SGD 59.29
Sera Pond Crystal Clear Filter Medium (Options Available)
Sera Pond Crystal Clear Filter..
SGD 151.80